Proper tuning, along with TxIntDelay, may improve traffic throughput in specific network conditions. .LP .B Copybreak .IP .B Valid Range: 0-xxxxxxx (0=off) .br .B Default Value: 256 .IP .B Usage: modprobe If the system is reporting dropped receives, this value may be set too high, causing the driver to run out of available receive descriptors. .IP CAUTION: When setting RxIntDelay to a And are you booting in legacy/BIOS mode or UEFI? –gertvdijk Jul 21 '15 at 17:24 @gertvdijk Post is updated! –Daniel Eckert Jul 21 '15 at 18:30 | show 8 modinfo e1000e | grep version Output: version: 1.4.4-NAPI srcversion: F3AE734BF9B60BE9BE2460E vermagic: 220.127.116.11-686 SMP mod_unload modversions 686 Load the driver module: modprobe e1000e Installing without a Network If a network card is
I fixed my Intel NUC non working ethernet by: download the driver from https://downloadcenter.intel.com/download/15817, currently 18.104.22.168 (as shown in lshw -C above) make install in the src folder rmmod e1000e modprobe Yes you're right. You signed out in another tab or window. If you need another lower bandwidth NIC, perhaps as a router, put the I219 on the slower link like the upstream Internet connection.
Much success for both of you, and welcome at Gentoo _________________If you want to see a Distro done right, compile it yourself! The user must reboot the system after applying the fix if changes were made to the EEPROM. All hardware requirements listed apply to use with Linux. I change that for a M and works well Back to top Display posts from previous: All Posts1 Day7 Days2 Weeks1 Month3 Months6 Months1 YearOldest FirstNewest First Gentoo Forums Forum
Back to top steak-sandwichn00bJoined: 27 Aug 2012Posts: 26 Posted: Mon Aug 27, 2012 11:13 pm Post subject: DONAHUE wrote: yes, as shown above by me, so that e1000e will be Back to top DONAHUEWatchmanJoined: 09 Dec 2006Posts: 7346Location: Goose Creek SC Posted: Wed Aug 29, 2012 2:21 am Post subject: After you selected
It is only supported as a loadable module. CrcStripping Valid Range: 0-1 Default Value: 1 (enabled) Strip the CRC from received packets before sending up the network stack. KumeranLockLoss Valid Range: 0-1 Default Value: 1 (enabled) This workaround skips resetting the Phy at shutdown for the initial silicon releases of ICH8 systems. What is a verb for "speak honestly"?
CAUTION: When setting RxIntDelay to a value other than 0, adapters may hang (stop transmitting) under certain network conditions. Ubuntu E1000e Trademarks Intel, Itanium, and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. iwconfig didn't show anything. Movie 80's/90's where humans are been replaced by cyborgs/robots Collision on self made hashing function Encode an integer Polyglot the (non constant) OEIS!
The real problem has to lay somewhere else. https://www.thomas-krenn.com/en/wiki/Installing_Intel_Network_Card_Drivers_under_Debian Markov country name generator What is purpose of an Undervoltage Sensing Circuit? Intel E1000e Driver Download ethtool is included with all versions of Red Hat after Red Hat 7.2. Linux Ethernet Driver Download Back to top vectornsn00bJoined: 23 Aug 2012Posts: 8 Posted: Tue Aug 28, 2012 1:08 pm Post subject: DONAHUE wrote: there it is: Device Drivers ---> [*] Network device support --->
Already have an account? Install the driver package: The drivers in the package have been compiled for the Debian kernel version 2.6.32-5-amd64 (2.6.32-35squeeze2). The BIOS version is the latest version. I simply did this from within Ubuntu for minimal effort.
In this case, the EEPROM needs to read "df" at offset 0x001e. E1000e Vs E1000 I had a look at the Linux 4.3 source code, finding that e1000e driver version was again bumped up to version 3.2.6-k. NOTE: The Intel® 82562v 10/100 Network Connection only provides 10/100 support.
Back to top steak-sandwichn00bJoined: 27 Aug 2012Posts: 26 Posted: Mon Aug 27, 2012 12:37 pm Post subject: Hi (R)andy, thanks for the link. Maybe you?Thanxvertiko vertiko Posts: 4Joined: 2014-03-28 14:23 Top Re: [SOLVED]Ethernet card intel I217-LM not recognized by Wh by vertiko » 2014-03-30 15:36 anyone? The values will be applied to each instance, in function order. Debian E1000e Thx! _________________If you want to see a Distro done right, compile it yourself!
Tags: hardware, intel, linux, networking Categories: hardware Updated: February 04, 2017 Twitter Facebook Google+ LinkedIn Previous Next Comments My Favorite Linux Terminal Font: Google Noto Mono 3 minute read Terminus font Proper tuning, along with TxIntDelay, may improve traffic throughput in specific network conditions. RPM functionality has only been tested in Red Hat distributions. The full GNU General Public License is included in this distribution in the file called "COPYING".
The maximum MTU setting for Jumbo Frames is 9216.